What would it take to build a breakout for the Gen Control PCB on a F900 Bmodel.
Category Archives: AircraftTroubleshooting
How do you use a DVM to sample a Thermocouple lead
How do I come to terms with the Primus 2000 “Download and Clear” BrewHaHa
If you get a “Avionics Maint” white message:
You can ignore it. Or you can go through a 1 YEAR hassle trying to get all of this stuff figured out..
Hart Aviation:
We build a Primus Data Loader, P-2000 Maintenance Access Unit, (Built to Honeywell Drawings). This unit was built for the roughly 19 Falcon 900’s that did not have built in data access ports. (See our web site under the Falcon 900 section near the end of the page) We have one on hand which sells for $4250.00.
F900ex S/N 028 the l42FV and R42FV are under the blank covers in the side consoles.
here is the written instructions:
F900EX Primus 2000 Download & Clear Procedures
MAU Drawing
What in the world is this?
1 year
Old Notes on VQ-BYT
F900EX Avionics Download 2017-05-15
This is the MAU drawing fir Modified F900SN022
How do I make peace with the Printer on BZZ?
Here is the last action when Hugo worked on it:
Hi Todd, below are the steps we took to fix the printer issue.
1. Wireless printer was configured to connect to some unknown wireless network. So we had to reset the printer when we took it back to the office.
2. We upgraded the firmware on the printer so that it could support air print. We enabled Bonjour on the printer.
3. Configured printer with IP address 192.168.1.173 and successfully connected it to the plane’s “VQBZZ Wireless Access” network
4. Tested printer successfully from windows laptop via wireless and iPad via air print.
Hugo E. Sanchez
How do I come to terms with AVTECH LED Strips
LED strip Flickers:
Intermittent solder connection from LED POwersupply Board to LED strip.:
And the cold solder joint that caused it:
The installation notes:
AvTECH_Flood LED installationP25D001C[1]
Crimpers:
CrimpersForAVTECH lighting63811-2800%20Spec[1]
Dies for crimpers:
The 63811-2800 number is a good number for the crimp tool handle (the Frame).
The die part numbers vary the part number of the pins being crimped.
Connector numbers:
Non Corrosive RTV:
| MSC Part #: | 00232025 |
|---|---|
| Big Book Page #: | 2167 |
| Brand: | Dow Corning |
| Mfr Part #: | 748-2455846 |
does falcon allow you to build breakout boxes?
here is the PDF workcard
StandardPractiseCardTSKFNXFIM10209001910901EA01
BreakOutBoxTSKFNXFIM10209001910901EA01
which Sealant is Which?
How do I come to terms with Fault Codes in a SPZ-8000 for F900?
Here is the simple break-in to get the codes:
REMEMBER::::::
If you pull the breakers in the air as a matter of troubleshooting, the codes are lost!
If you land and power down airplane, the codes are lost!
Flight Fault summary must be performed after aircraft lands, before power is turned off.
YD and MTRIM must be dark.
At the copilots left elbow in the engineers Panel.
There is a Bat Handle switch labeled “AFCS TEST” or some such.
Select it up.
The ID802 panels will self test.
Then , When they are finished you should see “01 – FGC TEST?” Do NOT perform the test now.
Instead, push the LAFCS button which in this case acts as a “Previous Screen” button.
A few screens back, you will get to “98 – FLGHT FAULT SUMMARY”
Push “RESET” to get to the flight fault screen.
That should show the codes for the LEFT computer.
Take a picture of that screen.
Now press reset again.
That should show the RAFCS faults.
Take a picture of that screen
+++++++++++++++++++++++++
Here is the Spreadsheet that unwraps the Hex code to plain english…. or as plain english as a Honeywell engineer can make it.
This one runs under Libre Office:
SPZ-8000-Flight-Fault-Summary .ods
This one runs under excel:
SPZ-8000-Flight-Fault-Summary – this one is from Augusta
here is an example fault code
Plain Text trouble shooting book:
how do markings on oxygen bottles work?
o2 bottle
http://www.usamma.amedd.army.mil/assets/docs/oxygen%20cylinder%20markings.pdf
How do I come to terms with Arduino-429 interface?
Here is a wonderfull 429 overview
airinc_429TheAvionicsHandbook_Cap_2
https://batchpcb.com/pcbs/73951 ia a universal converter project.
The fellows name is AllThumbs on VAF http://www.vansairforce.com/community/showthread.php?t=95229
http://www.vansairforce.com/community/archive/index.php?t-82604.html thread about the SL30 to Dynon HSI
http://www.instructables.com/id/Interfacing-Electronic-Circuits-to-Arduinos/ is a very nice explanation of a 429 to 232 converter
Here is the data from Niel on the frankenverter
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
here is a nice blurb on using a parallel port to test AIRINC 429 equipment
here is some detail abouthe labels
Here is the first Distillation of equipment labels
=============================================
2024 revival project
https://github.com/ncormia/FrankenVerter
https://github.com/ncormia/FrankenVerter/blob/master/a429.h
https://github.com/ncormia/FrankenVerter/blob/master/FrankenVerter.ino